Router trouble RT-AX88U

[ciprian.trofin]

My router is Asus RT-AX88U, firmware version 3004.388.6.

The 8 port switch is used as follows:
- port 1: desktop
- port 2: printer
- port 3: NAS
- port 4: powerline adapter
- port 5: Raspberry Pi running PiHole

DHCP is enabled on router. PiHole works only as DNS (DHCP disabled).

The router has WiFi hotspots on both 2.4 and 5GHz bands

The powerline network works as follows:
- one end is static, connected by Ethernet cable to router switch port 4
- the other end is WiFi enabled (2.4GHz only), serving a hotspot with the same SSID/credentials as the router. DHCP is disabled on this device. Devices connected to powerline hotspot get the IP from router.
The ideea for powerline is to extend 2.4GHz coverage.

FWIW, powerline ends connect each other @200Mbps.

The issue is the following: after working for a while (could be 3-4 days, could be a few hours after a reboot), the devices in range of powerline hotspot fail to get an IP address. The system log shows lots of consecutive DHCPDISCOVER / DHCPOFFER messages, not followed by DHCPREQUEST.

Mar  4 19:40:21 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:40:21 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:40:26 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:40:26 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:40:31 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:40:31 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:40:35 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:40:35 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:40:44 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:40:44 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:40:59 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:40:59 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:41:04 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:41:04 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:41:07 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:41:07 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:41:09 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:41:09 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:41:13 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:41:13 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:41:22 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:41:22 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:41:39 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:41:39 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx

Moving in router's hotspot range result in success:

Mar  4 19:42:11 dnsmasq-dhcp[1129]: DHCPDISCOVER(br0) 30:09:c0:xx:xx:xx
Mar  4 19:42:11 dnsmasq-dhcp[1129]: DHCPOFFER(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:42:11 dnsmasq-dhcp[1129]: DHCPREQUEST(br0) 192.168.76.10 30:09:c0:xx:xx:xx
Mar  4 19:42:11 dnsmasq-dhcp[1129]: DHCPACK(br0) 192.168.76.10 30:09:c0:xx:xx:xx

Resetting the powerline devices (power cycling) does not solve the problem. Rebooting the router does, but the problem shows again later.

I had the same problem with previous router, an N66U (using latest Merlin FW). I upgraded mostly because of additional LAN ports. I am aware of port 5-8 troubles, but I had none.

Any advice ?

 

[L&LD]

The issues with Ports 5-8 are random and obscure. This may be another variation.

To test properly, replace the PLAs with a wire (to test with). I'm going to guess the issue is repeated.

 

[adrenalize]

That's assuming its not a combined PLA with WiFi, so may not be possible to temporarily use an ethernet cable - but is the first step I'd try.

It does sound like an old problem I had way back around 4 years ago on 384.something - same thing in the logs the clients didn't do the request after an offer. Upgrading version nor full factory resets solved it, anywhere from 2-3 day to 2 weeks and it would come back.

I think restarting the dnsmasq service every week in a cron job kept it at bay. I tried every new release (with factory resets) but it persisted until about 386.x then magically disappeared. Not much help, I know, sorry!

 

[Wisiwyg]

Power gremlins? When was the power supply last changed? Is it the OE or an aftermarket? This is pretty non-specific, works sometimes, sometimes not. I've had these types of odd failures that were fixed with a new PS, even when the current one still 'worked'.

 

[ciprian.trofin]

Thank you for your kind advice.
I will investigate as much as I can, according your suggestions, however I lack some hardware...


To me, it looks like the client does not receive the DHCPOFFER message from router. Is there any way to investigate if the DHCPOFFER is sent to the correct interface?

To explain: the router is placed in a room, the WPA is in another (WPA - Wireless Power Adapter, check below)
To allow roaming, I setup the WPA hotspot the same as the router hotspot (if course, different channels). When I move between rooms with my phone, my phone connects to the strongest (signal) hotspot, sends a DHCPDISCOVER broadcast, the router responds with an DHCPOFFER... and that's all. If I'm not mistaken, the DHCPOFFER is unicast, it is sent only to the requesting device but this means different interfaces, according the hotspot:
1. if the hotspot is the router - the interface is wireless
2. if the hotspot is the WPA - the interface is a wired port on router


The powerline adapter consists of 2 units:
- TL-PA4010 (TpLink Power Adapter, basically a Layer 2 unit, connected by Cat5 to router and plugged in a power outlet)
- TL-WPA4220 (TpLink Wireless Power Adapter, it is the other end of TL-PA4010, it has assigned an IP address)
The powerline connection between adapters is stable (I cron ping the WPA unit every 10 minutes and there are no interruptions).

 

[ciprian.trofin]

For a while, I had no issues. After previous post, I installed scMerlin scripts, to allow me to restart dnsmasq service.

Today it showed again: when in range of Wireless Power Adapter, my device (phone) does not get an IP address; when in range of router, it does.

I tried (without restarting the router):
- restart dnsmasq service on router (via scMerlin scripts) - no improvement
- restart wifi service on router (via scMerlin scripts) - no improvement
- power cycle the Wireless Power Adapter - no improvement
- power cycle the Power Adapter (the one connected to router) - no improvement
- change the router port where the Power Adapter is connected - IT WORKED!

I find interesting that power cycling the Power Adapter does not solve my issue, but changing the switch (router) port did.

I also looks like my hunch about the router sending the DHCPOFFER to the wrong interface is plausible.

I there any way to reset (in software) the association between MAC addreses of devices and router interfaces ?