What's new

Use an AX82U after Masmovil fiber box in bridge mode

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

mlun58

New Around Here
I have got these parameters from my ISP (Masmovil) to setup my own router (RT-AX82U v2):

1) Username: h208@masmovil
2) Password: 123456
3) Vlan-id: 20
4) VPI: 32
5) IVC: 8
6) Encapsulation: PPPoE
7) Primary DNI: 212.166.64.1 (assume they mean DNS)
8) Alternative DNI: 8.8.8.8

I can easily setup 1-2-6-7-8, but I see nowehere to configure 3,4,5. Would have assumed this was somewhere under LAN - IPTV. But no.
Any ideas about how/where to add these?
 
Don't panic the settings are available, just in about the most obscure place possible!
WebUI > LAN > IPTV
Select ISP Profile: Manual Setting
Internet VID: X PRIO: X
1729622165835.png
 
Many thanks Crimliar:) I was actually around this screenshot, but couldn't see the relation to the three parameters. Tried to fill in like this - but doesn't work:
Internet VID: 20 PRIO: 1
LAN port 4 VID:32 PRIO:2
LAN port 3 VID:8 PRIO:3
Just a wild guess - cannot se the relation to Vlan-ID, VPI and IVC
 
Many thanks for your help! The fiber box is in bridge mode, and all parameters in the AX82U are to the best of my knowledge configured correctly (see below), but internet remains "not connected" after a couple of reboots of both the fiber box and the AX82U
1729678354557.png


1729678374353.png

Masmovil did not mention anything about configuring the ONT but something is clearly missing. My fiber box is a Sagem F@st 5655v2AC router. As far as I have understood it there are differences among using a separate ONT and a modem with build in ONT. I assume I have the latter.
 
If I were you I'd leave the 5655v2 in router mode and put the Asus in the DMZ behind it.
 
So you mean ignore the PPPOE settings and just use auto settings? Not sure I have the skills to setup DMZ :)
 
Yes. I'm not familiar with the 5655v2 but those sort of devices usually have an option to put a single device (i.e. your router's WAN connection) in the DMZ.

Of course you don't need the DMZ at all unless you want to allow remote connections from the internet to your network (i.e. VoIP, multiplayer gaming voice chat, VPN server, etc).
 
There is no "DIGI Smart Fibre" profile as far as I can see. Do you mean that "Manual" is incorrect? At least I couldn't make it work, so something prevents me for using a Bridge mode solution.
 
There is no "DIGI Smart Fibre" profile as far as I can see. Do you mean that "Manual" is incorrect? At least I couldn't make it work, so something prevents me for using a Bridge mode solution.
VLAN 20 is for DIGI but i checked also and it is for Masmovil too. It could be the bridge mode still controls the DNS. ie. no fully bridge mode. I was with a Spanish ISP a few years ago that did this. I think it was Movistar or Orange. The all in 1 router with ONT built in you could put in a type of bridge mode but you couldn't change the DNS. Look at your ASUS settings and make sure they wont affect that.
 

Latest threads

Support SNBForums w/ Amazon

If you'd like to support SNBForums, just use this link and buy anything on Amazon. Thanks!

Sign Up For SNBForums Daily Digest

Get an update of what's new every day delivered to your mailbox. Sign up here!
Top