Recent content by ginny

Yes I'm using the original ASUS firmware because it has (or at least had) better aimehs support specially for guest wlan support for guest network over the aimesh nodes. To mount external drives i use: cifs mount -t cifs -o user=abcd,password=123456 //192.168.1.62/harddisk /tmp/mnt/nas-1 nfs...

Thanks for your reply but the I test for that module I get: modprobe md4.ko modprobe: module md4.ko not found in modules.dep So maybe you can tell me where I can get the md4.ko module.

To mount an external NAS on the ASUS GT-AX11000 I borrowed the cifs and nfs modules from the Merlin firmware for this router, since the original ASUS firmware lacks those modules. The actual firmware from ASUS doesn't accept the cifs.ko or nfs.ko not and reports an error when I try to add the...

Thanks degrub. Even it has nothing to do with wireless

After adding an OpenVPN server on the ASUS GT-AX11000 router on firmware 3.0.0.4.386_45934-gb23bdac, the static DHCP table becomes empty. While applying the server the AX11000 makes a restart an all clients gen an IP address within the dynamic IP range. After adding some clients in the...

I deactivated the LED's using my way. The /jffs folder is nonvolatile and the data within /jffs survives are reboot or a power cylce. The steps below have only to be repeated after a factory reset. telnet router.asus.com or ssh router.asus.com using putty (telnet works as well from a command...

Hi Mattias The official Firmware has been released on Oct 22nd for some Routers. It's based on something between RC2-6 and RC2-7. See also the Thread Asus AC86U New Firmware - 3.0.0.4.386_40451-g30f1b6c All Routers applied with the official Firmware still follow the Beta path, as e.g. RT-AX92U...

@ASUSWRT_2020 I see on the official download page from ASUS the AiMesh 2 build Version 3.0.0.4.386.40451 from Oct. 22nd 2020. The latest RC2-7 has with 386.40577 a higher build number. From which Beta 386.xxxx version is the official firmware derived? Further I see not all routers which where...

Hi PretorianADB Sorry, regarding the spec for the switch i have no glue. As I saw somewhere in this tread, it has something with the VLAN handling to do. But it wasn't mentioned anything about the VLAN Id's. In my case I squeezed a second Cat 6 cable towards the living room. Another possibility...

Hi PretorianADB I assume you have already used the Router's LAN ports for other devices. I made some tests with Netgear switsches. I need IGMP Snooping enabled, since Swisscom uses Multicast for thier TV streams. Ethernet Backhaul Mode fails with the GS108Tv2 but it works with the GS105PE. The...

If you have the nodes connected over a managed switch "Ethernet Backhaul Mode" in the System Settings, it will fail always . I had that experience already. While I had set "Ethernet first" within the nodes it worked and and displayed Ethernet as Backhaul. But with this setup there was still a...

Here you are admin@RT-AC5300:/tmp/home/root# tc filter show dev br0 | grep -B1 0x80000000 filter parent 1: protocol all pref 3 u32 fh 822::800 order 2048 key ht 822 bkt 0 flowid 1:16 mark 0x80000000 0xc03f0000 (success 284242)

Hi livefeed Had the same problem, as well under RC2-4. When you when you set Ethernet only per node, clients can only establish a connection over the main e.g. internal WLAN on nodes with Backhaul over a switch. Guest cannot get a connection on nodes with Backhaul over a switch. I have seen as...

Hi ASUSWRT_2020 First of all Thank you for your great support bringing us to a final AiMesh 2.0 release. I assume you're speaking about the next release candidate which might be RC2-6. What's about the RT-AC5300 and RT-AC88U which stick still on RC2-4? Is it planned that these routers will...

Hi ASUSWRT_2020 What happened with the routers RT-AC5300 and RT-AC88U? After 10 days RC2-5 was released, there is still no update for these two models available. Are we in a dead end are what's the plan for these routers? Best regards Ginny