What's new
By:

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Recent content by joeejo

  1. J

    Cannot open router ui when connected to router via vpn

    Here is the router log May 28 22:16:24 Ranch ovpn-server1[30170]: 172.59.130.145:1335 VERIFY OK: depth=1, C=TW, ST=TW, L=Taipei, O=ASUS, OU=Home/Office, CN=RT-AX86U_PRO, [email protected] May 28 22:16:24 Ranch ovpn-server1[30170]: 172.59.130.145:1335 VERIFY OK: depth=0, C=TW...
  2. J

    Cannot open router ui when connected to router via vpn

    Thank you for your reply. That helped some, however using the lan IP the browser connects but the page is just a blank. Is there something I must set to allow the ui over the vpn?
  3. J

    Cannot open router ui when connected to router via vpn

    I have set up a vpn server on my asus RT-AX86U PRO using merlin 3006.102.4 using guides found here and at asus for the purpose of accessing the router UI from the intenet. I am able to connect to the router via the vpn server from the internet and I am able to ping the router, however when I...
    • joeejo
    • Thread
    • merlin vpn server webui not responding
    • Replies: 3
    • Forum: Asuswrt-Merlin
  4. J

    RT-AC86U (386.11) VPN no longer working

    Thank you. I will follow up on both suggestions.
  5. J

    RT-AC86U (386.11) VPN no longer working

    I am using OpenVpn CLIENT. and the only ovpn message in the log is (it repeats over and over): May 30 20:11:37 ovpn-client1[2088]: write to TUN/TAP : Invalid argument (fd=-1,code=22)
  6. J

    RT-AC86U (386.11) VPN no longer working

    I upgraded RT-AC86U to 386.11 and the internal VPN would no longer connect. I did a clean upgrade of the firmware. I am using OPENVPN with a dedicated IP and it has worked fine for years. Once I downgraded back to 386.9 the VPN connected immediately without issue. Is this a know problem with...
  7. J

    Solved openvpn issue with 386.7_x

    Thank you for your prompt and most helpful response. As I began to follow your instructions I discovered several iptables entries that were put there a while ago to facilitate port forwarding on my vpn IP. I had forgotten about them. They are no longer needed and several of them conflicted with...
  8. J

    Solved openvpn issue with 386.7_x

    I am having two issues with openvpn which I believe are connected. I am using an RT-AC86U router. I have tried using version 386.7_0 and 386.7_5 with the same result. (factory reset before upgrades) When VPN connects, I do not get the confirmation IP address, but rather it says “Public...
  9. J

    AC86U VPN issue 386.7.0

    The ports are open on the vpn tunnel and actually your original post gave me the answer...a clean install of the new firmware resolved the issue completely.... Thank you for your assistance.
  10. J

    AC86U VPN issue 386.7.0

    The vpn does work outbound (myip shows correct vpn IP), however, I cannot access my open ports from outside my network when it shows "UNKNOWN" public ip. Thank you for the response
  11. J

    AC86U VPN issue 386.7.0

    I have a dedicated IP address with my vpn supplier. When the VPN client is enabled, the router reports the Public IP address in Merlin-Asus v386.5.2, however once I upgrade to 386.7.0 the VPN reports the public IP as "unknown". Once I downgrade to 386.5.2 and the Public address is reported...
  12. J

    386.5 cannot change client name

    Thank you for the advice. A factory reset seems to have corrected the issue.
  13. J

    386.5 cannot change client name

    Thank you for your reply. I have tried from the client list button from the main page, from the LAN > DHCP Server page (for those assigned static ip addresses) and from the "client status" list (appears on the right after clicking on the monitor in the circle above the client list button on the...
  14. J

    386.5 cannot change client name

    I am running merlin 386.5 on an Asus RT-AC86U router. In previous version I was able to change the name of the client (see attached image), however since the I upgraded to 386.5 the changes are not saved when I click 'apply'. Am I doing something wrong or is this a possible bug?
  15. J

    Upgrading RT86U to RT88U same configuration

    Is there any way to used the saved configuration from my RT-AC86U (Merlin 386.3.2) to install on a new RT-AC86U (Merlin 386.3.2)? I am trying to avoid manually configuring the new router to my existing config. Thank you
See more
Back
Top
✖