jffs

Hello, I replaced my old AC86U Pro router with BE86U Pro. Of course, I loaded the new version 3006.102.5 of the Asus-Merlin software. Everything was fine until I installed the Skynet add-on. Then the circus started with the saved settings in the WAN and System tabs. Half of the settings changed...

Hi I am trying to load a custom JFFS script to my RT-AX55 so that I can enable configuration for Cloudflare DDNS but I am struggling with knowing how best to go about this. I can ssh fine into the router but there's no SCP, text editor, or standard FTP. Theres a folder for an FTP client but when...

Hi! When I power on/reboot my AC86-router, it runs the '/jffs/scripts/wan0-connected' script twice. I can also see the wifi appear, then disappear after a few seconds and come back again after a few more seconds. This causes the commands in the above said script to be run twice and in...

Hi! I have a recent backup of the jffs partition (tar archive). I need to restore the vnstat database from it (no configuration or settings, only the database). Which files and folders do I have to extract from the tar file to the dn-vnstat.d folder? Is it simply the complete folder "csv"...

Hi! I'm wondering what "usb" means if set it as storage location? Where is the exact location? I've got an external SSD drive attached to my router and entware is installed on it. Will that be automatically used? And in which directory will the database reside? I'm asking because I've lost my...

There is an ASUS TUF-AX5400 router with the latest Merlin (388.2_2_0-gnuton1) firmware. How can I limit the speed of downloading data from a specific site (or at least from several IP addresses) on this router? I do not need to limit the speed of the entire specific device. I also do not need to...

My RT-AX86U seems like it might be dying. I'm on 388.2_2 merlin firmware, with a few scripts added. I've had a few problems recently that may or may not be related. I'll jot them down here... - A week or two ago, I saw error entries in the log for 'command failed', seemingly when trying to...

So i made a script at "/jffs/scripts" (the folder scripts wasnt there, so i made it) Enabled JFFS custom scripts and configs on webui chmod 777 file services-start The script runs ok when i manually execute it "/jffs/scripts# sh services-start" but it won't launch on start up This is content...

I am a beginner when in comes to this, my area has frequent power outages, I want the router to check if my PC is on at every boot, and if it is off, to turn the PC on using Wake on LAN. My understanding is that if I want a script to run at boot, I should put it in the /jffs/scripts/ directory...

I have used optware in the past on WD NAS systems and other boxes so I know basically what entware does. However the instructions for installing it on asuswrt-merlin seem many and varied! :) The first question is - do I really need it? The only program I want to add to my RT-AC68U is rsync...

Hi ! Great firmware as guest networks are finally in their own subnets, and mesh for guest network works too :) Anyway, like title says my RT-AX58U router gets new WAN IP in every reboot from my ISP. It's quite annoying as before moving to this AX58U my IP stayed same for more than a year. I...

I recently ran into a full JFFS2 system at /jffs due to bloated /jffs/.sys/TrafficAnalyzer folder. df reports that /jffs is 100% used on my router, and due to the design of JFFS, files can't be removed or edited if the disk if full. Therefore following commands are useless in this case...

I just recently installed scMerlin to the jffs partition on my ASUS RT-AC86U router and it is working just fine. However, today i tried to setup dnsmasq.conf on the jffs partition and i'm getting an error for no space left on device: admin@RT-AC86U-7860:/jffs/configs# pwd /jffs/configs...

I had updated firmware from 384.16 to 384.17 a few hours earlier. Everything seemed ok, but I had just switched OFF Enable Share in USB Application - Network Place (Samba) Share / Cloud Disk and I was investigating an interesting looking new error I'd noticed in the General Log: httpd...

Hello, I have followed the instructions here : https://github.com/RMerl/asuswrt-merlin.ng/wiki/Policy-based-Port-routing-(manual-method) Here is my nat-start #!/bin/sh sleep 10 # During the boot process nat-start may run multiple times so this is required # Ensure duplicate...

Hi, I.ve read many threads on how to achieve this and had partial success. Please guide me in the correct direction. Many thanks in advance. I have a Router/Modem/IPTV thing that my ISP installed me, which has the internet connection. It has a network of 192.168.1.0. This will be router 1 and...

Hi! I just found out that /jffs/scripts/wan-start is also run when the wan interface is stopped, e.g. by command 'halt'. I found out by letting this script email me a message when WAN starts (works great), but I also receive the email when I halt the router before power is turned off. A reboot...

Hi everyone I am the proud owner of 2 cheap ipcams, made in China and notorious for causing all sort of security issues. I also intend to save in the cloud whatever those would capture, using a paid-for cloud service. I understand there is a need to open ports on my firewall, and the cloud...

Hello I have a problem with VPN settings . Here is my previous topic https://www.snbforums.com/threads/openvpn-configuration-ip-leak.50334/ I used the way with jffs firewall script, to block wan . And it seemed to me that everything was ok, but lately i had power outage, so the router and...

As far as I know, in order to make a user changes based on filesystem (configs, or software) in bare router I have to enable JFFS, where Merlin refers for critical scripts, then dump changes every time I reconfig something. 1) But do I need JFFS, when there is a USB HDD is attached, and I do...