Scott Hunter
Occasional Visitor
Set up... Tried more than one way. Stock on all and Merlin on all. Full resets via WPS or Rest button depending on router. New ssid each time / step
Started again today from scratch As far as removing my pi4 and re-install of HA. (Still not even powered on yet or connected for the first time.
Cleared Cache on all browsers (chrome/Edge)
Re-installed app. (asus) android
* Before Starteing all this i hooked up old Nighthawk and connected and left all switches/ what ever on it. * Nothing was to connect to asus but the main P/C for set up
Ac86u is main. ( reset from merlin to stock. Logged back in then used Web gui to reset again/ then started full config.
Ac88u followed the same after config on 86u was done. Ethernet from 86u-88u. and AImesh completed and shows up fine.
All seamed well. So pluged in all hard lined ( Just the Cameras and Set up P/C )
Then With Laptop on the night hawk logged into each Tasmota Device and Reset them then added the wifi for 86u. Got about 10 done and getting the same issues that made me do all this. Constant disconnects and unable to enter Web GUI of Switches.
Setting are stock wand Smart Connect Is on.
1. Settings = Should I be changing some things around?
2. IP adresses = Each device still connected to the (Prior) IP it had even with all these resets. (Why)?( The device names did change back to stock ) Like=Tasmota-xxxx
3. All Devices updated ... Only new thing I had going on was Google started telling me things were not secure anymore. Router/Devices all when entering web page GUI's..
So in Short.
Ac86u+(node) AC88u Aimesh backhauled over Lan
90% Of the Devices are MartinJerry or Treatlife on latest Tasmota(10.0)
Devices show on router / Then Disapear .. Sometimes i can get into their GUI sometimes not. Its almost like their trying to Stay in AP mode to help share the signal.
Either way here is a log of a device(Via tasmota GUI) .. I noticed the long and many attems to connect then finally does. I have no clue where to see same on the router side !
00:14:40.343 WIF: Connecting to AP1 AsusFree in mode 11n as tasmota-7A22FB-0763...
00:14:53.009 WIF: Connect failed with AP timeout
00:14:53.348 WIF: Connecting to AP1 AsusFree in mode 11n as tasmota-7A22FB-0763...
00:15:05.009 WIF: Connect failed with AP timeout
00:15:06.342 WIF: Connecting to AP1 AsusFree in mode 11n as tasmota-7A22FB-0763...
00:15:19.004 WIF: Connect failed with AP timeout
00:15:19.343 WIF: Connecting to AP1 AsusFree in mode 11n as tasmota-7A22FB-0763...
00:15:27.005 WIF: Connected
00:15:27.256 HTP: Web server active on tasmota-7A22FB-0763 with IP address 192.168.1.71
Started again today from scratch As far as removing my pi4 and re-install of HA. (Still not even powered on yet or connected for the first time.
Cleared Cache on all browsers (chrome/Edge)
Re-installed app. (asus) android
* Before Starteing all this i hooked up old Nighthawk and connected and left all switches/ what ever on it. * Nothing was to connect to asus but the main P/C for set up
Ac86u is main. ( reset from merlin to stock. Logged back in then used Web gui to reset again/ then started full config.
Ac88u followed the same after config on 86u was done. Ethernet from 86u-88u. and AImesh completed and shows up fine.
All seamed well. So pluged in all hard lined ( Just the Cameras and Set up P/C )
Then With Laptop on the night hawk logged into each Tasmota Device and Reset them then added the wifi for 86u. Got about 10 done and getting the same issues that made me do all this. Constant disconnects and unable to enter Web GUI of Switches.
Setting are stock wand Smart Connect Is on.
1. Settings = Should I be changing some things around?
2. IP adresses = Each device still connected to the (Prior) IP it had even with all these resets. (Why)?( The device names did change back to stock ) Like=Tasmota-xxxx
3. All Devices updated ... Only new thing I had going on was Google started telling me things were not secure anymore. Router/Devices all when entering web page GUI's..
So in Short.
Ac86u+(node) AC88u Aimesh backhauled over Lan
90% Of the Devices are MartinJerry or Treatlife on latest Tasmota(10.0)
Devices show on router / Then Disapear .. Sometimes i can get into their GUI sometimes not. Its almost like their trying to Stay in AP mode to help share the signal.
Either way here is a log of a device(Via tasmota GUI) .. I noticed the long and many attems to connect then finally does. I have no clue where to see same on the router side !
00:14:40.343 WIF: Connecting to AP1 AsusFree in mode 11n as tasmota-7A22FB-0763...
00:14:53.009 WIF: Connect failed with AP timeout
00:14:53.348 WIF: Connecting to AP1 AsusFree in mode 11n as tasmota-7A22FB-0763...
00:15:05.009 WIF: Connect failed with AP timeout
00:15:06.342 WIF: Connecting to AP1 AsusFree in mode 11n as tasmota-7A22FB-0763...
00:15:19.004 WIF: Connect failed with AP timeout
00:15:19.343 WIF: Connecting to AP1 AsusFree in mode 11n as tasmota-7A22FB-0763...
00:15:27.005 WIF: Connected
00:15:27.256 HTP: Web server active on tasmota-7A22FB-0763 with IP address 192.168.1.71