What's new

pixelserv pixelserv - A Better One-pixel Webserver for Adblock

  • SNBForums Code of Conduct

    SNBForums is a community for everyone, no matter what their level of experience.

    Please be tolerant and patient of others, especially newcomers. We are all here to share and learn!

    The rules are simple: Be patient, be nice, be helpful or be gone!

Yep, you do need pillow time for sure because it's iOS 13 [emoji16][emoji16]
There's that number again. I hope my code is more accurate.
 
Looks like iOS 13 had made it to Thailand iPhones. Friend of mine posted this morning.

upload_2019-9-20_9-45-21.png
 
Hello,

I think I have a problem with pixelserv-tls. It never seemed to work...
Diversion is updated to 4.1.4 and Pixelserv is started and running, I have the Pixelserv CA certificated installed in the Windows Trusted cert store.
upload_2019-9-21_13-47-50.png



I have also installed uiDivStats and the Pixelserv statistics report shows 404 Not Found.
upload_2019-9-21_13-45-48.png


Perhaps someone knows what I did wrong?

Thank you.
 
Hello,

I think I have a problem with pixelserv-tls. It never seemed to work...
Diversion is updated to 4.1.4 and Pixelserv is started and running, I have the Pixelserv CA certificated installed in the Windows Trusted cert store.
View attachment 19378


I have also installed uiDivStats and the Pixelserv statistics report shows 404 Not Found.
View attachment 19377

Perhaps someone knows what I did wrong?

Thank you.
uiDivStats - WebUI for Diversion statistics
New version of uiDivStats available.
 
Thank you for the notice, I have updated uiDivStats to the latest version 1.2.1, but the Pixelserv Statistics Report section still shows 404 Not found...
You enabled Access Restriction in Administration/System after the Diversion installation.
Diversion checks for it during installation but not afterwards.

Add a rule with "Destination IP" being your pixelserv-tls IP and the "Access Type" being "Web UI" then hit "Apply.
 
You enabled Access Restriction in Administration/System after the Diversion installation.
Diversion checks for it during installation but not afterwards.

Add a rule with "Destination IP" being your pixelserv-tls IP and the "Access Type" being "Web UI" then hit "Apply.
Well... I'm locked outside...
The Access Restriction was off and I just added one single rule to allow pixelserv to webui...
Now I can't connect to the WebUI nor SSH.

Is there a way to undo this without resetting the router?
 
You enabled Access Restriction in Administration/System after the Diversion installation.
Diversion checks for it during installation but not afterwards.
It does check it now, I've silently pushed an update that checks if pixelserv-tls is in the Access rule list.
Use u and force update Diversion.
 
Well... I'm locked outside...
The Access Restriction was off and I just added one single rule to allow pixelserv to webui...
Now I can't connect to the WebUI nor SSH.

Is there a way to undo this without resetting the router?
Well, that was not a very good idea. I did not ask you to enable it, just add the rule IF Access restriction IS enabled.
 
Is there a way to undo this without resetting the router?
I think what might work is this since the pixelserv-tls IP has access to the Webui:
1. Unplug Router from power source
2. Remove attached USB device(s)
3. Power up router
4. Manually set one of your devices to the pixelserv-tls IP
5. Log in to the Webui
6. Remove access restriction
7. Disconnect that device with the manual IP
8. Unplug Router from power source
9. Plug in USB device(s)
10. Power up router
 
I think what might work is this since the pixelserv-tls IP has access to the Webui:
1. Unplug Router from power source
2. Remove attached USB device(s)
3. Power up router
4. Manually set one of your devices to the pixelserv-tls IP
5. Log in to the Webui
6. Remove access restriction
7. Disconnect that device with the manual IP
8. Unplug Router from power source
9. Plug in USB device(s)
10. Power up router

Thank you, I was thinking of the same solution.
The only USB device connected is the one where Entware is installed.

I can't do this now, because I'm away from the router, but I'll do it when I return.

Cheers!
 
Thank you, I was thinking of the same solution.
The only USB device connected is the one where Entware is installed.

I can't do this now, because I'm away from the router, but I'll do it when I return.

Cheers!
Sorry for your troubles, but the access restriction is the most obvious cause from my point of view for your original problem.
 

Similar threads

Sign Up For SNBForums Daily Digest

Get an update of what's new every day delivered to your mailbox. Sign up here!
Top