Release ASUS RT-AX86U Pro Firmware version 3.0.0.6.102_34406 2025/10/28

[bbunge]

Can't have consecutive same characters? Dumb. 3 or 4 in a row I understand, but not 2.

Use letters and make one cap the next lower case. Such as XxYy13579!

 

[iFrogMac]

Another password suggestion, is if you're on a Mac, use Safari's auto password generator, and then copy and paste the password into your desired browser. That's what I do with all my sites now, and it works well.

 

[pkozerski]

Guys, wanted to ask you, after dirty upgrade everything works?, no need to factory reset if i do not want ?

 

[jksmurf]

Guys, wanted to ask you, after dirty upgrade everything works?, no need to factory reset if i do not want ?

Normally, yes, everything works. But there are caveats:

• Sometimes (very occasionally) the supplier of the FW will state you should do a factory reset. Do one.
• After a change in codebase from e.g. 3004 to 3006 branch (wich may not apply to you) a factory reset is an absolute. Do one.
• After changing FW from Stock to Merlin or vice versa, a factory reset is highly recommended.
• After a big jump in versions even on the same codebase a factory reset is highly recommended.
• If you're having issues with something on the new FW that were not apparent on the previous FW a factory reset is highly recommended.
• If you have been updating and downgrading FW without doing a factory reset for a while i.e. lots of dirty updates, then from time to time a factory reset is highly recommended.

 

[bbunge]

Guys, wanted to ask you, after dirty upgrade everything works?, no need to factory reset if i do not want ?

You are correct. If it works for you, great! But it is a good idea to take a settings backup before you upgrade and be prepared to roll back if problems arise.
I am still unsure why I had problems with the upgrade. It is working OK for now so I will leave it for a while.

 

[bbunge]

Something weird is going on with this firmware. I know Network Map is wonky but when Ethernet connected clients that are connected to the router show up as wired clients to the AiMesh node, which only has WIFI clients, something is wrong!
Am going to roll back to 102.34349 for a bit...

 

[maxbraketorque]

Something weird is going on with this firmware. I know Network Map is wonky but when Ethernet connected clients that are connected to the router show up as wired clients to the AiMesh node, which only has WIFI clients, something is wrong!
Am going to roll back to 102.34349 for a bit...

That's been happening to me forever. But people seem to have a range of experiences with Network Map.

 

[NoLight]

Something weird is going on with this firmware. I know Network Map is wonky but when Ethernet connected clients that are connected to the router show up as wired clients to the AiMesh node, which only has WIFI clients, something is wrong!
Am going to roll back to 102.34349 for a bit...

Not seeing that on my aimesh node. But i think this has been a know issue that sometimes pops up with the icons.

 

[bbunge]

Back up and running on 102.34406. I suspect my "issues" were the result of a corrupt upgrade and a reset that failed to clear all the settings. Even a hard factory reset did not work to clear the settings. I believe the Ethernet connected clients showing up on the AiMesh node was the result of the failed reset and the use of the former node as the router. Sounds complicated but...
To fix my problem I removed the node (which was the original router) from the mesh, factory reset from the GUI then did a hard factory reset. With the unit WAN not connected I flashed 102.34349, did a minimal setup, factory reset from the GUI then a hard factory reset. I then did a full manual setup with the WAN disconnected. When that router was working I swapped it out with the other AX86U Pro to avoid internet down time to not upset the family. I then did the same reset, flash 102.34349 and reset to the other AX86U Pro to get it ready as an AiMesh node. Added the node to the router and let the system run for a while. After a while I did an upgrade to the router and node from the GUI to 102.34406. No complaints from the family!