Release Asuswrt-Merlin 386.2 is now available

[killeriq]

Each radio band, 2.4 and 5 GHz, has three possible Guest networks. Left to right they are called Guest 1, 2 and 3. They do not have to be use in order. In the 386 codebase the left most Guest network for each band has the ability to sync to AiMesh nodes to enable each node to have the same Guest WIFI. Without getting into the nuts and bolts of how this works I can confirm that it works well on Asus factory firmware and Merlin Firmware.
However, reports are that you can get some odd "error" messages in the log. The Guest 1 network still works and is secure. Ignore the log if it bothers you.
Also, it has been discovered that the WIFI clients on Guest 2 are not isolated from the LAN clients and may pose a security risk. I feel it is better to use Guest 1.

Thanks for explaining, but i dont use any Guess Network

 

[banger]

Just a small thing. When doing a Wifi scan it interrupts streaming. I can understand why but should it?

 

[menaceinc]

I can't access the main page of my router after updated. I did clear cache and tried on different devices

 

[MvW]

Depending on how long it has been since you last updated the firmware, it might be doing some maintenance in the background. This can take some time. Just wait patiently and try to access the UI later.

 

[brummygit]

Hi @RMerlin - I just tried to turn off download shaping in Cake by setting the bandwidth value to zero ( 0 ). Unfortunately the field validation doesn't allow this despite the error message saying that 0 is a valid entry.

 

[Mutzli]

I have been using 3 AC68U routers with the latest merlin firmware ( I use aimesh 386.1_2)
So I started updating the firmware to 386.2
First update went to mesh node nr1, which is wireless. Firmware updated ok.
Second I updated mesh node nr2, which is backhauled by ethernet. This node fails to update. Tried a few times, rebooted, same result: fails to update.
Third updated the main router. Updated fine.

Tried to update mesh node nr2 several times after that and each time it just fails to update.
I get the login screen , put user/pw in, then select update file and it say uploading 0%, this takes a while and it switches back to the screen that has the uploads button on it and nothing happens.
I tried the following things:
removed node and reset the node by pressing reboot button for a while, re-pair the node, then upgrade. fail
removed node and reset the node by pressing pws butotn for a while, re-pair node, then upgrade. fail.
Put node in wireless mode only (disconnected backhaul ethernet cable), upgrade fails.
I used chrome browser and also tried on edge browser. Made no difference.

I know I can upgrade it by resetting it and connecting it directly to my laptop and upgrade the firmware, but why does it not upgrade while in regular use as a node ??? And the other does upgraded just fine.?
Any tips appreciated.

Try again with node (nr1) turned off or disconnected from th main router.

 

[geekwithoutacause]

Try again with node (nr1) turned off or disconnected from th main router.

I tried that too. Same result.

 

[menaceinc]

Depending on how long it has been since you last updated the firmware, it might be doing some maintenance in the background. This can take some time. Just wait patiently and try to access the UI later.

I have been waiting for a while now. Once I did manage to have the login, but then blank page.

 

[Butterfly Bones]

I can't access the main page of my router after updated. I did clear cache and tried on different devices

Note this from release notes of 384 to 386? (as noted by MvW above)

NOTE: Some users upgrading might have to go through some
database maintenance on first boot, which means the
router might be slower or have a non-responsive webui
for a while.
This can take anywhere from 5 minutes up to an hour,
depending on your model, just give it time to complete
the process.

 

[geekwithoutacause]

Another issue I noticed on my setup. I can telnet into my main router's ip address no problem. But when I telnet into one of my ai mesh nodes, I get access denied after giving it id/password. Should be the same as the main router ? Or do I need to set that up first after resetting it ( after which I paird it as a node)

 

[menaceinc]

Note this from release notes of 384 to 386? (as noted by MvW above)

Ok, I'll wait patiently. Thanks for the quick reply!

 

[archiel]

Another issue I noticed on my setup. I can telnet into my main router's ip address no problem. But when I telnet into one of my ai mesh nodes, I get access denied after giving it id/password. Should be the same as the main router ? Or do I need to set that up first after resetting it ( after which I paird it as a node)

if you can ssh (I am assuming you meant ssh rather than telnet) into the main router, then you should be able to ssh onto any connected AiMesh node with the same credentials, there is no need to setup anything on the node in advance. What ssh client are you using and what is the error message?

 

[geekwithoutacause]

if you can ssh (I am assuming you meant ssh rather than telnet) into the main router, then you should be able to ssh onto any connected AiMesh node with the same credentials, there is no need to setup anything on the node in advance. What ssh client are you using and what is the error message?

I use putty, portnr 22

 

[archiel]

I use putty, portnr 22

and the exact error message you are seeing.?

 

[geekwithoutacause]

and the exact error message you are seeing.?

Well.... lol. As I tried to login again to make a screenshot to show you, it logged me in just fine !. Does it take a while for these settings to transfer to the node from the router after setting up as a node????

 

[dazedandlost]

This method may be completely unsupported. Use at your own risk... it will probably brick your router, burn your toast, and make your hair fall out.

Thank you for this. I'm ok with the risk even if it kills/reincarnates/both/neither Schrödinger's cat.

 

[archiel]

Well.... lol. As I tried to login again to make a screenshot to show you, it logged me in just fine !. Does it take a while for these settings to transfer to the node from the router after setting up as a node????

Once the router and node have settled down after the initial upgrade there shouldn't be any delay, but stuff happens.

 

[geekwithoutacause]

Once the router and node have settled down after the initial upgrade there shouldn't be any delay, but stuff happens.

Well, thanks for the help. I ftp'd the new firmware over and then did a firmware upgrade from the shh session. All updated now.

 

[[Daniel]]

Add me to the list of folks who successfully upgraded, in my case from 386.1_0 to 386.2_0 on an AC86U. Cleared/refreshed the browser cache, and all the new images loaded like the OP notes said.

The only issue I have found so far is a minor graphical/UI one in Client Status:

1. Chose to filter wireless devices by 2.4G, yet the "search bar" brings up the 5G details
2. Chose to filter wireless devices by 5G, and the "search bar" brings up "undefined" details
3. Wait a few seconds after #2, the Wired tab completely disappears, then reappears after a few more seconds
4. if you go elsewhere in the UI and come back, you can repeat the issue at will

Upgraded firmware yesterday, waited until today to ensure things "settled", rebooted router, cleared/refreshed browser cache, and the graphical/UI issue persists.

 

[csj97229]

The only issue I have found so far is a minor graphical/UI one in Client Status:

1. Chose to filter wireless devices by 2.4G, yet the "search bar" brings up the 5G details
2. Chose to filter wireless devices by 5G, and the "search bar" brings up "undefined" details
3. Wait a few seconds after #2, the Wired tab completely disappears, then reappears after a few more seconds
4. if you go elsewhere in the UI and come back, you can repeat the issue at will

I also see this behavior on both of my RT-AC86U units running 386.2. Definitely weird, but it doesn't seem to cause any real problems.