Recent content by rkk2025

I'm on AsusWRT Merlin 386.7_2 and I have both Runner and Flow Cache HW Acceleration enabled while I have Wireguard running in a site-to-site setup + a couple of single peers to connect to my LAN from the outside if necessary. I did have to modify the Wireguard "amtm" script to prevent it from...

I'm unable to repro the performance issues from (Wireguard - Session Manager - Discussion thread (CLOSED/EXPIRED Oct 2021 use http://www.snbforums.com/threads/session-manager-discussion-2nd-thread.75129/) | Page 13 | SmallNetBuilder Forums) on my RT-AX86U with AsusWRT 386.7. Have a Site-to-Site...

Yes, I'm indeed actively using Wireguard for a permanent Site-to-site connection (With the Wireguard addon script enabled). I have "fc_disable=1". I change it to =0 and will see how that affects Wireguard. I also had to change wg_manager.sh to avoid having it disable Flow Control on every boot...

Hi, I'm trying to get "Flow Cache" to be "Enabled" in my RT-AX86U. I had previously AiProtection enabled and had briefly "Adaptive QoS" enabled too to experiment with it. As far as I'm aware these are the most common options that are mentioned that could Disable "Flow Cache". So now I have...

Hi, thank you all for the suggestions. I just noticed with the last beta firmware that I have NVRAM usage 65460 / 65536 bytes Running the nvram unset commands from @Rudi did not change anything. I will report back after factory resetting the router (When I finally find some time)

Oww, ok. That sounds like good news. I'm on 384.13 and it's always stuck saying "Searching please wait". If I go to "View List" it just says "No data available". I haven't tried with a factory reset for a while. Will try with that first. Thank you for the good news!

Hi, Since a few versions ago, the list of connected devices (Not sure how it was called, network map or so) seems to be completely broken on my AC68U. From what I remember this is an upstream Asus issue, but it has been now going on like this for months (half a year so far?). Has there been...

Hi, I like to have my Guest Network and private LAN separated from each other. I have also a small web server at home, and I have set the DNSmasq server to point to the local IP of the server, to avoid having the data go trough my slow internet and back to my LAN (I'm in a double NAT setup, so...

Hi, this seems to have been going on for a while now, I don't know with which upgrade it started, but it still happens on the lates AsusWRT Merlin Firmware 384.10_2, altough it has been happening already in previous versions. A complete factory reset and reflash didn't help at all. It seems...

Hi, Seems like the Bandwith Monitor in the QOS Section is not working anymore. It is showing most of the time a bandwith of 00.0 for both upload and download, every now and then it jumps to 0.01. I have dissabled HW acceleration, and in the Debug Console of Google Chrome I can see that...

But how can I run a process without it to being closed after wan-start finishes? From what I understand if I detach the ssh process (With &) once the script that launched the it finishes, all child (inclusive detached ones) get all closed. What's the best way to keep the process running in the...

Hi, Is there any way to create a custom service in a asuswrt-merlin router? What I'm basically trying to achieve is to create a reverse tunnel to expose my openvpn server to the internet by using the "serveo.net" which allows to do that trough ssh. But for that I need a way how to start the...

Do you know if there is any similar software like the AsusWRT implementation that can be used on non Asus hardware?

Hi, Since I enabled the Trend Micro Two Way IPS on my AsusWRT and seen how well it performs (In terms of Network Speed and detected attacks), I would not change it back to how it was before. At some point I needed to change to another router with an OpenWRT, and I've seen that Snort/Suracata...

Hi, Is it possible to connect my RT-AC68U (With AsusWRT-Merlin) to another AP (Just like a Wireless Repeater) while keeping the "Wireless router mode"? I want to keep a NATed subnet (With its own DHCP) that should not be accessible from outside, the "Wireless Repeater" mode doesn't fulfil that...