vlan

  1. T

    Create dhcp client interface on Asus router.

    Hi all, I’ve got asus3200 and trying to setup a vlan listening on dhcp, so it can get address from the box connected to it. How do I do that? I mean I created the vlan, i just don’t how to make it listen on dhcp? I know there is udhcpc for wan interface eth0, is it the way to go? Teymur
  2. ThePooBurner

    Is there a script for configuring VLANs?

    Hi everyone. I've been scouring this forum for a couple months now looking for information on using VLANs via scripting and trying to make sense of everything that I've read. I'm not making this post lightly, as in most of what i've read there seem to be a lot "You should have searched first...
  3. M

    I need "guest" wifi in other AIMesh nodes....?

    I am not sure how to go about this. My main router I have 2 additional "guest" wifi network. One for people that come over to our house and one for strictly IoT devices. both on different subnet using YazFi I added another AIMesh capable router but I need those two guest network to work as...
  4. toaruScar

    Guest network for wired devices

    I have a device in my network that I don't fully trust but earns me passive income. I want to isolate this device with only internet access. This divece is hooked directly to the ethernet port of my ZenWiFi XT8, and has no Wi-Fi capabilities. I think a guest network meets all my requirements...
  5. R

    Setting up VLANs on AC68P

    Hey all, I use my AC68P as an AP, and I'm trying to get VLAN tagging working on it. I've had some success but I think I need some help to complete this. I want router to have the following VLANs: VLAN Physical Ports Wireless 1 (Default) WAN, LAN1, LAN2, LAN3 2.4G / 5G 20 2.4G / 5G 30...
  6. Kelbesq

    Got VLAN taggin working on my AP's guest SSID - do I need a managed switch?

    After some effort, I got VLAN tagging working on one of my ASUS AP's running asuswrt-Merlin "working". My setup is: an EdgeRouter 4 an Netgear GS308 unmanaged switch. RT-AC66U_B1 + RT-AC3200, both ASUS products running in AP mode with the latest non-beta Asuswrt-Merlin). I'm using...
  7. F

    wrong VLAN tags going out

    Hi all, I'll try to be brief. I have AC3100 in AP mode with 2 guest WIFIs. I want each guest WIFI to go out over on WAN port on its own VLAN (I am using IDs 9 and 10). To that end, I have /jffs/scripts/services-start script as shown below. When a client connects to WIFI wl0.2, it is assigned...
  8. K

    AiMesh and guest WiFi on node

    Currently AiMesh nodes do not support guest WiFi. I have two RT-AC68U (384.17), one as a router, the other one as the AiMesh node. I would like to have the same guest WiFi on the AiMesh node as on the router with the guest clients being isolated from each other and the internal network. This...
  9. G

    VLAN tagging with stock firmware

    Hi all I definitely need a new router, as my AC56U with Merlin fw is at the end of its life (clients randomly loosing internet connection, web interface not reachable and so on). My setup is now made by a FritzBox 7530 is managing VDSL/VoIP/DECT (doesn’t support bridge, my VDSL provider does not...
  10. H

    IEEE 802.1Q for RT-AC66U_B1

    Hi, If I make a TRUNK port on the switch and mark all traffic using IEEE 802.1Q tags, does the ASUS RT-AC66U_B1 understand the router? I uploaded the latest Merlin FW to this router. I ask because I found no mention of tagging. Thanks for the anwers
  11. G

    Looking for a RT-AC56U substitute

    Hi all I'm looking for a substitute for my 5 years old AC56U. I had no big problems so far with it, but I now begin to see it's limit with my increasing (30 devices so far, 25 static DHCP entries, 5 port forwardings,2 guest networks, AB Solution ad-blocker, NTP server,VLANs) home network. I...
  12. B

    RT-AC5300: SPAN/bridge eth1 (WLAN) port

    Wireless Router Mode Firmware 384.15 Hello and thanks for allowing me to participate in SNB forums! I'm an IT admin with pretty good grasp of networking/linux/etc and am trying to solve an issue and could use some advice: I run a packet analysis platform whose capture interface does not have...
  13. W

    CPU high usage AC1900U/AC68U. VLAN related?

    Hello! I have just installed a AC1900U (AC68U) in my home. I’ve carried out a pretty basic installation, 3.0.0.4.384.45717 . A hard reset plus define SSIDs, remove upnp, define some static Ip and that’s all. No Aimesh, Ai protection or openVPN. The only relevant configuration apart from the...
  14. H

    LAN - Route

    hi, I have a smart switch on which I have several VLANs, including ACL rules. ASUS router RT-AC66U-B1 with the latest version of merlin FW is connected to VLAN10. In the router RT-AC66U-B1 on the LAN - Route tab I have set routing rules for individual VLANs. In the switch I have set the traffic...
  15. JensM

    NAT acceleration in AP mode?

    Sorry for opening 2 threads in a short time but this is not related to my other post. I have an AC66U with Johns Fork running in AP mode. When setting up multissid with vlan tagging (the tags then are send to my opnsense which is doing the rest) I had a big issue. When first connecting to any...
  16. JensM

    Is there a limit of number of bridges / vlans?

    After switching to opnsense as my mainrouter, I'm using my AC66U (running Johns Fork) in AP mode. I'm scripting it to tag different SSIDs and LAN-Ports with VLANs and send the traffic via a single connection to the opnsense what worked quite well for some SSIDs. For some others WPA2...
  17. M

    Topology/setup help - Mostly Asus-merlin devices

    Hi guys, guru, network and problem-solving lovers! I am requesting your help and wisdom here :) I know this question is mostly about topology but my devices are mostly using Asus-merlin and I believe the solution to my questions could be solved using the firmware. My situation is as follows...
  18. fantasydreamerforever

    Wireless VLANs on Asus RT-AC88U

    Hey all, I was trying to assist in getting some VLANs set up on a friend's network to segment off their IOT devices, but they keep all their IOT devices configured on the main wifi, and I'm not 100% on the best approach to take for segmentation in this instance. I'm trying to avoid encouraging...
  19. B

    IOT security question: Seperate a Smart TV from rest of network.

    I hope can explain this correctly. My goal is to separate a Smart TV IP Address from the same IP range as the rest of our home network. Currently I have an ADSL modem that is acting purely as a bridge to the ISP provider and that is all it does. Then I have a consumer router (Netgear r6250)...
  20. skeal

    [RESOLVED] Need basic port based vlan help

    Hi I have three TL-SG108E smart switches. Named as: North, South, and Main. On North and South I have identical settings. 2 x 802.1q port based vlans. They are setup, one has a PVID of 2 the other 8. I setup two 802.1q vlans on the Main switch to separate the North and South switches, all...
Top