switch configuration

I'm having network problems here at my video production company. We have a modem with internet of 500 Mpbs download and 250 Mpbs upload. On a daily basis, we are 15 people connected to the Ubiquiti wifi network + 4 people via cable Here's my setup: Modem+Router -> switcher (connected to 10...

Hi everyone. I'm pretty new to home networking. A while ago I setup an OpenWRT WiFi Router and that was quite complicated but I got it working. I'm now trying to better understand networking as a whole and design my own home network. I have been planning to build a NAS for file sharing, etc. and...

Hi SNB Peoples, I had a GT-AXE11000 until i dropped it this weekend. Like really badly. Like Paul Walker in a Porsche GT bad. I have ordered a GT-AX6000 to replace her, unlike the AXE11000 the AX6000 has Dual 2.5GbE ports. What I want to know is the following: I am going to plug my 1 Gig...

So I bought a Netgear GS116Ev2 about 18 months ago and it stayed in the box until recently as I had to move house and then became far too ill to do anything very much for about a year. Now I'm feeling a bit better, I've just discovered it doesn't support LACP: The manual states: The switch...

I have a Zyxel XS1920 smart managed switch https://www.zyxel.ch/de/support/download/201962_1/ I want to use it just as a unmanaged switch; like a QNAP QSW-1208. So I don't need it to be smart, I just need it to be simple so I can plug it in to extend an existing network. Can anyone advise in...

Hello, I am wondering if I can get advice on how to set this up. I have a regular networking router with my ISP and I have another with an VPN installed on it. I wish to connect these routers to broadcast two SSID on my access points. (one with regular internet from my ISP and another with VPN...

Hi All, I'm trying to identify which ports in the back of the R9000 are eth1 and eth2 respectively, I know all are in the same switch but I want to break apart the switch and use those eth1 and eth2 independently, each has its own MAC address. Any ideas where do I need to look into the Voxel's...

Hi everyone, I am attaching my current/ideal configuration, but I'm not sure how to configure vlan on the switch. In detail I have a Tplink TL-SG105E managed switch connected to the router. I have a raspberry pi 3b + already configured and working with vpn (mullvad vpn). What I would like to do...

Hi I have three TL-SG108E smart switches. Named as: North, South, and Main. On North and South I have identical settings. 2 x 802.1q port based vlans. They are setup, one has a PVID of 2 the other 8. I setup two 802.1q vlans on the Main switch to separate the North and South switches, all...

Anyone know how to so this. Ports are getting locked and we're going nuts.

I've searched and read lots on this topic, and now I must say I'm more confused than anything else. Can someone offer me advice, on how to stop two devices on my network from communicating with the other devices of my Lan. These devices require nothing else other than internet access and have...

As mentioned in title, I am looking for more information on if a switch will pass VLAN tag/header that was assigned by the Access Point, on to the router. I was recently able to snag a Netgear ProSafe GS728TP for $50, and want to understand potential impacts to my home network. My setup has...

The TEG-082WS switch supports a feature called Storm Control. How do you determine an appropriate value for a port's Threshold that would support the purpose of Storm Control ?

Thank you in advance for the forum. I am new to this switch business and need help. I have comcast cable internet service. An Arris SURFboard SB6190 Cable Modem connected to an Arris SURFboard AC3200 WiFi router. I would like to add a 2950 switch to give me some more ports. I do not want...