merlin

Hi, I bought a TUF AX5400 router and just discovered it has this merlin firmware on it. For the life in me i cant get it removed. Its running - 386.07_2-gnuton1 I tried factory reset in admin menu \ restore , that didn't work. Uploading ASUS firmware ASUS TUF-AX5400 Firmware version...

Hi! i installed rtorent using rtorrent-easy-install on my merlin-entware installation. The service start, gui is ok but one time rtorrent go down (i suppose when test dwonload finish). Syslog information are very poor: where I can find more infos? Thanks to all!

Hello guys, I am very new to all this, so please be patient. I got my first aftermarket router Asus Ax11000 just this very week, and it was simply awesome with the stock firmware. However, I faced some issues when adding pihole, and everything I read pointed me to using Merlin. First...

I've just setup a AI mesh network using two AC86U running Merlin 386_11 and want to see the wireless log of all AI mesh clients. However, in the System log > Wireless log menu, I could only see devices connected to the main router, not the mesh node. Can anyone show me how? Thanks

I have an ASUS RT-AX88U router that is running RT-AX88U_388.2_2 firmware. I have a Guest Network setup that I use to connect to every day when working from home. I had my router set so that every Monday night at 5am, my router would perform a scheduled reboot. However, when it does this, my...

Hello, I have a RT-AX82U V1 with stock Firmware-Version:3.0.0.4.388_22525 It doesnt matter which merlin gnuton version I choose, its always says "failed Can anyone help me? kind regards

RT-AX86S - Merlin 388.2.2 try to install with AMTM entaware terminal freeze here. I can do? (for installing i used the diversiti site option) Thanks Olind0

I am running a GT-AX6000 on Merlin 388.2. When the computer is directly connected to the router with an ethernet cable I get horrendous lag spikes every 20-30 seconds or so. It will take my frame rate from 180fps down to 20-30fps for a couple of seconds and then it goes away only to do it...

Hello! I can't connect my OpenVPN client on RT-AC68U router (Asuswrt-Merlin version 386.11) to OpenVPN 2.5.5 (linux) server. I couldn't connect even after I changed the default port and protocol to 55777/TCP. But: I tried to connect from a smartphone with the configuration file as below...

Hi, I have two GT-AXE16000 routers. One primary, and one that I was trying to use as an AiMesh node. The problem I'm getting is that the node constantly resyncs and restarts wireless (as seen in its log), with only a few seconds of actual uptime in between each resync. This results in an...

https://www.twingate.com/ Would it be possible to run this on the router? apparently it can run on a pi? Would it work as an AMTM addon? looks like a tiny install. Is it safe regarding Twingate being in control of the controller? Trusted by some small businesses, Safe for home use...

Hey there, sorry if this has been answered before - I have looked and can't find a similar question. I'm not a networking expert before I begin! have just upgraded to MerlinWRT and Mullvad is my VPN of choice. As a side note I'd like to use wireguard but they only have instructions for openwrt...

I'm trying to setup a dyn dns service called deSEC. I have a dyn subdomain sub.dedyn.io. In the newest version of inadyn, deSEC will be supported, but there is an older version in Merlin's firmware. So I need to make a custom config. In /jffs/configs/inadyn.conf.add I have a couple of extra...

Hi, can we achive AiMesh technology on assus ac3200 in anyway ? by default AiMesh is not available in ac3200.

Currently have an RT-AC86U (with NextDNS CLI for devices not routed thru the VPN) and upgrading to a new RT-AX86U. I'd like to minimize the amount of manual rework as possible when setting up the new router. I have about 50 different rules in VPN Director and 8 different OpenVPN clients setup...

I have a modem running on bridge mode and every-time there's a power outage my RTAX86U (version 386.7_2) gets a local WAN IP instead of a public IP. It should be getting like this below. But the router stops doing the query once it gets an IP even tho a local IP which don't have internet access...

I've noticed that in the last version XT12 was supported by Merlin but I see that XT8 is not supported yet and I have not seen any threads talking about this Any plans on supporting this device?

Anyone running an OVPN client on an ax88u Pro yet? What kind of speeds are you getting ? Where do you top out? Thanks!

Hi, Looks like my attached usb drive may have bitten the dusk. I am getting the following errors and my cpu cores are both constantly at 100%. DNS to website loading is taking a long time. What is the best way to go about replacing a currupt usb with minimal disruption ot he rest of my set...

I had been running 384.19 on AC86U for a number of years as I had various problems with updates after that build. I took the leap to upgrade to 386.10 yesterday and it would appear the issues I had with previous updates have gone. As the VPN section now has the VPN Director to control device...