[ 3006.102.5 alpha Build(s) ] available build(s)

[KevTech]

Where are these options at?

Useless smart connect.

 

[maxbraketorque]

Just upgraded my AX86U Pro main/AP combo from 3004.388.4 to this firmware. Zero issues. All settings preserved. VPN works. IoT network works (although now on a different subnet). Manual DHCP assignments remained. Connected USB drives work and still have the correct permissions. This was as easy as it gets.

 

[bluepoint]

Useless smart connect.

Which category? In wireless?

Update: NVM I found it. Never used it, hence, not familiar with that options.

 

[octopus]

This vpn client refresh button doesn't do anything, same with wireguard.

 

[RMerlin]

This vpn client refresh button doesn't do anything, same with wireguard.

View attachment 66376

Is the public IP supposed to have changed?

 

[Dedel66]

After 24 hours can tell that everyrthing is up and runnung smoothly but found this in syslog:

"Jun 22 12:57:34 kernel: Oops: Stuck in CPU#1 for more than 5 sec; break the loop!
Jun 22 12:57:34 kernel: Oops: Stuck for more than 5 sec; break the loop!
Jun 22 12:57:34 kernel: CPU#0: 0
Jun 22 12:57:34 kernel: CPU#1: 1
Jun 22 12:57:34 kernel: CPU#2: 0
Jun 22 12:57:34 kernel: CPU#3: 0 "

Never saw that before...

 

[redbird71]

Where would I find a more detailed changelog to what 37957 brings to the table?

 

[octopus]

Is the public IP supposed to have changed?

I had to wait until vpn provider change ip nummer.
I thought the spinning wheel would spin when I pressed refresh, but it didn't.
Seems to working without spinning wheel.

 

[RMerlin]

Where would I find a more detailed changelog to what 37957 brings to the table?

You can't. There's no changelog with these code drops.

 

[RMerlin]

I had to wait until vpn provider change ip nummer.
I thought the spinning wheel would spin when I pressed refresh, but it didn't.
Seems to working without spinning wheel.

There's no spinning wheel because the page does not get reloaded, and it only takes 2-3 seconds at most. An Ajax call is sent to the web server, and the response is retrieved, and updated on the existing page.

 

[Dedel66]

Again a little "hiccup":


Jun 23 12:51:39 kernel: eth5 (Int switch port: 5) (Logical Port: 5) (phyId: 11) Link DOWN.
Jun 23 12:51:44 kernel: eth5 (Int switch port: 5) (Logical Port: 5) (phyId: 11) Link Up at 2500 mbps full duplex
Jun 23 15:26:16 kernel: Oops: Stuck in CPU#2 for more than 5 sec; break the loop!
Jun 23 15:26:16 kernel: Oops: Stuck for more than 5 sec; break the loop!
Jun 23 15:26:16 kernel: CPU#0: 0
Jun 23 15:26:16 kernel: CPU#1: 0
Jun 23 15:26:16 kernel: CPU#2: 1
Jun 23 15:26:16 kernel: CPU#3: 0

I did NOT switch anything off...

 

[GaselK]

IoT network (Guest Network Pro) online schedule still not working properly.
Devices being in offline period still can connect to IoT network.

 

[FernandoF]

@dave14305 and/or @RMerlin,

Would this test/release cycle for 3006.102.5 be a good opportunity to correct the "Control D (Network Security)" IP addresses in the DoT drop-down list, which were identified too late in the 3006.102.4 cycle?
Or do we need to strictly follow the list provided by Asus?

For details (and sources), please refer to the message below:

Release - Asuswrt-Merlin 3006.102.4 is now available

Asuswrt-Merlin 3006.102.4 is now available. There are a number of significant things to note with this release: 1) BCM4912 models are now migrated to this 3006 code base. This includes the following device list: GT-AX6000 zenWifi Pro XT12 GT-AX11000 Pro GT-AXE16000 RT-AX86U Pro RT-AX88U Pro...

www.snbforums.com

In summary, what we should have for "Control D (Network Security)" is the following:

TLS Hostname: p1.freedns.controld.com

IP Addresses:
76.76.2.11
76.76.10.11
2606:1a40::11
2606:1a40:1::11

Or, in the commit format:

        {
            "dnspriv_label" : "Control D 1 (Network Security)",
            "dnspriv_server" : "2606:1a40::11",
            "dnspriv_server" : "76.76.2.11",
            "dnspriv_port" : "",
            "dnspriv_hostname" : "p1.freedns.controld.com",
            "dnspriv_spkipin" : ""
        },
        {
            "dnspriv_label" : "Control D 2 (Network Security)",
            "dnspriv_server" : "2606:1a40:1::11",
            "dnspriv_server" : "76.76.10.11",
            "dnspriv_port" : "",
            "dnspriv_hostname" : "p1.freedns.controld.com",
            "dnspriv_spkipin" : ""
        }

Thanks in advance for your attention.

 

[dave14305]

Thanks in advance for your attention.

I’ve sent an update for review. Are you using the new settings manually? Any issues?

webui: Update Control D DoT labels and IP addresses by dave14305 · Pull Request #878 · RMerl/asuswrt-merlin.ng

Rename the dropdown menu items for Control D DoT to align with the free DNS choices offered on the controld.com website and update the DoT IPs to match the guidelines given at the link below: https...

github.com

 

[FernandoF]

I’ve sent an update for review. Are you using the new settings manually? Any issues?

Thanks, Dave, for submitting the update. I've recently switched to Quad9, but yes, I was manually using the settings from my previous message without any issues.

In order to double-check the IPv4 and IPv6 addresses for the 3 profiles you've submitted (Malware, Ads & Tracking, Family Friendly), I've just sent an email message to Control D. I'll inform as soon as I hear back from them. Thank you.

 

[dave14305]

In order to double-check the IPv4 and IPv6 addresses for the 3 profiles you've submitted (Malware, Ads & Tracking, Family Friendly), I've just sent an email message to Control D.

I read their docs on how to configure stubby on Linux for the desired configuration.

Linux

How to configure Control D on any Linux computer.

docs.controld.com

 

[FernandoF]

I read their docs on how to configure stubby on Linux for the desired configuration.

Excellent, thanks for sharing the link!