ipv6

Hi! I'm trying to set up openvpn server to let clients connect using the router's ipv6 address, but failing. My openvpn server is working fine over ipv4, but my ISP in the UK uses carrier-grade NAT, and I don't want to keep paying for a static IP address. Any help or clues regarding what I could...

Router: RT-AX88U Firmware Version:386.1_2 Enabling IPv6 after getting my ISP to enable it for me. The router is advertising itself as my DNS despite my settings to use my own Pihole as my DNS. Is there something I'm missing in how it is configured? pi@raspberrypi:~ $ ip -o addr 1: lo...

Due to the lack of IPv4 public IP address, we hope to use IPv6 to connect OpenVPN to access the intranet. The actual test is available. We only need to modify the protocol proto tcp-server To be amended as follows: proto tcp6-server Can Merlin add it to the management page?

Hi all. I have some questions about Vpn and IPV6. Actually my confusion is mostly about ipv6. Since 2015 when all the stuff about ipv6 was starting to emerge, i tried to understand how it was going to be handled for new and legacy devices. I didnt understand at that time and i decided to wait to...

Topology Two ASUS routers: 1st plugged into a modem (w/ WAN aggregation) 2nd plugged into the first router both are in router mode and not set up as an AP One of the reason I opted for this setup is that I liked the idea of having a firewall on the client-router in order to apply some more...

I have noticed that IPV6 is no longer functioning on my Orbi. I have tried all Voxel FW versions since .19 without success. Currenly on V9.2.5.2.5SF-HW. IPV6 had been working in the past. I do not think it is directly related to a FW version, but maybe something happened on my router during...

I am looking for a way to make some IPv6 routes persistent in my router. Thus far I can add the routes via ssh to the route with a command similar to below. route -A inet6 add 26XX:XXXX:XXXX:XXXX:1000::/68 gw 26XX:XXXX:XXXX:0001::2 dev br0 The only issue I have is after every reboot the...

I've been struggling with my AC66U (old rev.) speed issues, finally I narrowed it down to IPv6. When I enable 6in4, my speed over ipv4 gets capped at around ~130-150 mbps, and router is lagging like crazy (ICMP 20-30ms, unresponsive web), as soon as I disable IPv6, I get ~700-900 mbps without...

Hi, I would like to configure a static local IPv6 address prefix (as defined by RFC 4193 Unique Local IPv6 Unicast Addresses) on my RT-AC87U router using Asuswrt-Merlin. After looking at the documentation, I cannot find a way to do that. Any idea? I already enabled SSH connection if that is...

Hi My ISP provides me with a permanent 48 bits IPv6 prefix (e.g.: 2001:1234:5678::/64). I have a fully functional IPv6 connectivity when using DHCP-PD (Prefix Delegation) aka "Native" connection type in my RT-AC87U router using Asuswrt-Merlin. However, I would like to set the prefix...

Sorry for poor english. I tried to find ways to enable DS-lite on Asus merlin. And I tried to setup it manualy but "ip6_tunnel" is not found in modules.dep I think odhcp6c supports DS-Lite but I could not find a way to enable it. I found a script for DS-lite in here...

Hello all Maybe my question is stupid, i apologize if so, but somehow i feel that answer is not that obvious. My ISP does not provide IPv6 at all. Should i keep IPv6 on my router disabled or i should enable it anyway? If i should enable it, then which connection type should i pick?

Netgear R7800 with Voxel latest firmware ddns client editing help needed. In what file is located the dynamic dns http api url via telnet? I would like to manually add ipv6 address as text to api command that router sends to dynamic dns servers within ip update. Because now if i set manually...

Hi There So I have an AC86U running merlin 384.16 I use Airvpn config However I have found an issue which I have contacted Airvpn about who responded with the message at the bottom of this post. basically when I use the following config option including "Push Peer info" the vpn refuses to...

When using DNS over TLS, with filter set to router, do the DNS setting on the IPv6 page bypass the filter? I have them set to the same values as listed in the the 'DNS-over-TLS Server List' on the WAN page. Currently on the ipv6 page I have the 'Connect to DNS Server automatically' set to...

Hi, I have IPv6 enabled on my Orbi system. I ran an app that tells me what my current DNS servers are. This is what I get: Primary DNS: fe80::a204:60ff:fe1e:2e5a Secondary DNS: 10.0,0.1 What is that primary address? The secondary I know since that the Orbi's internal IP. The reason I ask...

Hello SNB! I'm aware that it's possible for devices to request/have multiple IPv6 addresses, but my lists are getting what I would consider to be excessive? Is this normal operation? Also, what is the advantage/purpose of "Release prefix on exit" under IPv6? Would this help to minimize the...

Hi, I figured out that in my dual-stack environment my Clients get for IPv4 my router's DNS IP but for IPv6 my Client's get the Providers DNS. My expectation would be to also get the router's IPv6 (the local one) for DNS. :/ I Use DHCP-PD and it works so far. Also I set up DoT on WAN settings...

Hello, I know you dont want to introduce full vlan support for good reasons. In Poland we have Orange FTTH service being probably the most popular fiber provider. I managed to get Funbox 3.0 (router with built in ONT) with separate ONT (so i can replace Funbox 3.0 with my RT-AC88U FW 384.15)...

Hi, I have a issue with my AX88U. I set up the Openvpn server to: use VPN to access both LAN and WAN advertise DNS to clients no extra custom config. The case is when I connect to the router from a client that has both IPV4 and IPV6... only the IPV4 traffic is routed through the tunnel whereas...